Zum Inhalt springen

English:Design & Technology Year 7 - Electrical and electronic systems

Aus MOOCsWiki Staging
aiMOOC-Siegel aiMOOC

Design & Technology Year 7 - Electrical and electronic systems

QR-Code



Introduction

A button is pressed, a controller applies a rule, and a light changes. Where does the information enter, where is the decision made, and where does the energy come from? Learn to explain an electrical or electronic product without confusing its functional diagram with its wiring.

Use drawings, the supplied fictional states and paper traces. No circuit assembly, powered experiment, heating, motor connection or mains electricity is required. Real electrical work must use school-approved equipment, the correct supplied power arrangements and direct supervision. A low-voltage label alone is not a safety guarantee. Year 7 is an editorial placement within Key Stage 3; online completion is not a practical electrical qualification.


Identify supply inputs control and outputs by their roles

An electronic product combines a source of electrical energy with components that receive information, apply a rule and produce a useful effect. A system diagram helps you explain those roles. Start by naming the system boundary: are you studying the entire product, its controller, or one component? The same physical item can have different roles in different uses, so classify its function in the chosen system rather than only its appearance.

The power supply provides energy in a suitable electrical form. An input device supplies information about a user action or a condition. A control element uses that information to determine the intended output. An output device produces an effect such as light, sound, heat or movement. Information arrows explain the relationship between stages; they do not mean that the small input signal necessarily supplies all the energy needed by the output.

For a fictional desktop request indicator, a push button is the input, an electronic controller applies the rule, and a light-emitting diode, or LED, provides a visible output. The supply powers the system. Pressing the button is information about a request; the button is not the main energy source. The controller may be a suitable electronic circuit or a programmed processor, depending on the design. Not every product needs the same implementation.

Afrank99's photograph of six through-hole LEDs with two leads each. It shows component form; colour and appearance do not establish safe current, voltage, polarity or a complete circuit design.
Afrank99's photograph of six through-hole LEDs with two leads each. It shows component form; colour and appearance do not establish safe current, voltage, polarity or a complete circuit design.

An LED is used here to emit light. A buzzer or speaker can create sound; a suitably designed motor or other actuator can create movement; a heater is an output when its purpose is to produce heat. These outputs serve different functions and need appropriate electrical arrangements. A heater is not interchangeable with an LED and a controller signal is not automatically suitable to power a motor. You are comparing roles, not selecting real component ratings or wiring a power device.

A sensor is an input in a system that measures a condition, such as light level or temperature. It provides information; it is not the output merely because its reading appears on a display. The display is a separate output role. Context matters: some devices can have multiple roles. For example, the micro:bit documentation explains that its LED display can emit light and also be used to sense light. Name the role actually being used instead of claiming that every LED always has exactly one possible purpose.

Keep supply, information and effect separate in a component-role table. For each entry write what it contributes and what remains unspecified. The indicator's colour does not tell you whether it represents 'request', 'busy' or 'fault'; that meaning must be defined by the design. A clear label or symbol alongside colour helps users who cannot distinguish the chosen colours.


Distinguish a functional diagram from electrical connections

A functional system diagram represents the intended flow of information: input, control and output. For the request indicator, write 'button state to controller rule to LED request indication', then show the supply as a separate energy input. This description explains what should happen but does not show each wire, terminal, current-limiting component or component rating. It is not a complete manufacturing or connection drawing.

A circuit diagram uses symbols and connection lines to represent electrical relationships. It answers a different question: which terminals and components are electrically connected? The lines are not necessarily the physical positions or shapes of wires inside a product. A circuit layout and a functional flow diagram can describe the same system in different ways; neither should be mistaken for the other.

Mets501's schematic has one cell symbol and three resistor symbols in a single loop. It illustrates series connections, not an LED controller or the full request-indicator circuit.
Mets501's schematic has one cell symbol and three resistor symbols in a single loop. It illustrates series connections, not an LED controller or the full request-indicator circuit.

Read this actual image from the unequal parallel lines at the left, representing a cell, around the single loop containing three zigzag resistor symbols. There are no drawn switch, LED or processor symbols. Trace the continuous path through each resistor and back to the cell. The picture supplies no resistance or supply values, so it cannot establish a particular current, brightness or suitability for making. Do not silently reinterpret the three resistors as three LEDs.

For a separate simple conceptual cell-switch-lamp circuit, an open switch breaks the intended conducting path and a closed switch completes it, assuming suitable intact components and supply. That simple direct switch control does not itself contain a separate electronic decision processor. In the request-indicator system, the button can instead provide information to a controller, which then drives an appropriately designed output circuit. Both can respond to a switch, but their internal arrangements differ.

An LED normally needs appropriate polarity and current limitation as specified for its circuit. Do not infer those details from lead appearance, casing colour or the generic series diagram. A real circuit requires the correct component specifications, connections, supply and school-approved check. Joining supply terminals directly with a conductor creates a short circuit; it is not a substitute for a load or an experiment to perform. Even low-voltage sources can cause overheating or other harm if misused.

Use known approved educational equipment and its own current manufacturer's guidance for any later school practical work. Do not use damaged equipment, improvise power sources, open mains-powered products, connect unknown peripherals or investigate faults while energised. Report uncertainty to the teacher and leave the proposed work pending. This course provides no actual connection or device-control instructions.

For interpretation practice, produce two labelled paper representations: a role diagram for the request indicator and an explanation of the shown cell-and-resistor circuit. Write the information each provides and the missing information that prevents construction. An accurate 'not shown' statement is better evidence of understanding than inventing a hidden controller in the picture.


Trace a responsive rule and choose an appropriate output

Original fictional rule: while the request-indicator supply is available, illuminate the request LED only when the system is enabled and the push button is currently pressed. The output follows the current conditions; it does not remember an earlier press. Let E mean enabled and P mean pressed. A value of 1 means the condition is true and 0 means false. These are logical values, not measured voltages or instructions for a physical pin.

Enabled E Button pressed P Intended request LED
0 0 OFF
0 1 OFF
1 0 OFF
1 1 ON

The controller uses an AND condition: both E and P must be true. In the first three rows at least one condition is false, so the intended output is OFF. In the fourth row both are true, so it is ON. This table describes the intended behaviour of a powered, functioning conceptual system. It does not establish what a damaged circuit would actually do.

Trace a sequence with the system enabled. At first the button is released, so the LED is OFF. Press it and the LED becomes ON. Hold it and the LED stays ON. Release it and the LED becomes OFF. Press again while disabled and the LED stays OFF. A rule that toggles on each press, or keeps the LED lit after release, would be a different specification. State which behaviour is intended before writing tests.

The power supply is separate from the enable input. In this model, disabling tells the controller not to show a request; it does not claim that every internal circuit is physically disconnected. If no energy source is available, the LED cannot produce its normal light merely because the logical conditions are true. An OFF indication alone does not distinguish a released button, disabled state, missing supply, broken connection or failed output.

Plan cases before judging the product. Test every combination in the table, a continued hold, release after a press, a disabled press and the no-supply case. Keep expected and actually observed results in different columns. All results in this lesson are predictions from the stated rule; no device was tested. If a real output differs, document the mismatch and ask the teacher to manage the approved checking procedure rather than changing wires or increasing the supply.

A sensor can replace a user input in another design. For a separate fictional automatic display, define D as 'the light reading is below 40 on this invented scale' and show its indicator only when enabled and D is true. A reading of 39 meets that condition, but 40 and 41 do not. The scale is not lux, a real sensor calibration or a recommended lighting threshold. Missing or uncertain readings should be recorded as unresolved information, not invented measurements.

Choose an output to meet a user need. A visual request can use a labelled light or display. A sound may attract attention without looking at the panel, but volume, setting and users' hearing needs matter. Movement can indicate a position but introduces moving-part and power questions. Heat is useful only when the product actually requires a thermal effect and demands specialist safety consideration; it is not a suitable decorative substitute here. Combine channels thoughtfully rather than assuming louder or brighter is better.

The optional ESA video provides a simulated LED context. A repeating blink is not the same behaviour as the current-state request rule above. No account, circuit building, code transfer or copying of demonstrated connections is required. The written lesson supplies the full role explanation, truth table and test cases.

Submit a conditional design explanation: intended user and output, supply and component roles, rule, representations, expected cases and remaining implementation questions. Distinguish conceptual correctness from actual circuit performance and teacher-observed practical competence. The system should be understood before any physical implementation is considered.


Interactive Tasks


Quiz: Test Your Knowledge

Which role provides the energy for the fictional electronic indicator? (The suitable power supply) (!The meaning of the word request) (!The button label alone) (!The truth table by itself)



Which is the input in the original request system? (The push button providing its current state) (!The LED emitting the request indication) (!The output sound if a buzzer were selected) (!The light produced by the output)



What does the control element do? (Uses input information to determine the intended output) (!Always replaces the power supply) (!Automatically makes every physical connection safe) (!Guarantees that no component can fail)



How is a light sensor classified when measuring a condition for the controller? (As an input providing information) (!As the final light output merely because it has a reading) (!As proof that all LEDs only emit light) (!As a supply that must power any motor)



What is actually shown in the supplied series schematic? (One cell symbol and three resistor symbols in one loop) (!A complete LED request controller with a button) (!A microprocessor and four sensors) (!A mains-powered heater with verified ratings)



What does a functional system diagram mainly explain? (The roles and intended information relationship between stages) (!Every exact terminal and wire of a finished product) (!The safe current of every component in a photograph) (!A guarantee of lifetime reliability)



What is the intended request LED state when enabled but not pressed? (OFF) (!ON because enabled alone is sufficient) (!Permanently latched from any earlier press) (!Unknown because the stated table has no such case)



What happens when the button is held while enabled under the stated rule? (The LED stays ON until a relevant condition changes) (!It must toggle on and off with every instant of the hold) (!The supply automatically becomes infinite) (!The circuit is proved safe for every load)



Which fictional light reading is below the stated threshold of forty? (39) (!40) (!41) (!49)



What does an OFF indication alone establish? (The visible output is off while several different causes remain possible) (!The button must definitely be released) (!The supply must definitely be present) (!The entire system has passed every test)





Memory Game

Supply Source providing electrical energy in a suitable form
Input Information entering the chosen system
Control Applying a rule to determine the intended response
Output Useful effect produced by the system
Sensor Input device measuring a condition
Truth table Record of an intended logical result for each stated input combination





Drag and Drop

LED indication A light output in the chosen use
Buzzer indication A sound output
Heater function A heat output needing a justified purpose
Motor function A movement output
Push button state An input representing a user action





Crossword Puzzle

SUPPLY Source providing the system with electrical energy
INPUT Information entering the chosen system
CONTROL Role that applies the response rule
OUTPUT Useful effect produced by the system
SENSOR Device measuring a condition for the system
CIRCUIT Electrical arrangement represented by connections and symbols





LearningApps

Optional extra practice. Choose an appropriate activity with your teacher. If the external collection is unavailable, use the native activities and independent tasks in this course.


Cloze Text

Complete the explanation.
The electrical energy comes from the

. Information enters through an

. A

can measure a condition. Applying the response rule is the

role. The useful effect is an

. A light-emitting diode is abbreviated

. A connection representation is a

diagram. The two-condition request rule uses

.



Open Tasks


Easy

  1. Classify the product roles: Identify supply button controller and LED in the original request indicator. Explain the difference between information and energy roles.
  2. Observe the media: Describe the LED component photograph and trace the single loop in the actual schematic. Name which components and ratings are not shown rather than inventing an LED controller in the drawing.
  3. Read the truth table: Explain every enabled and pressed combination in words. State the assumed availability of power and the meaning of the logical values.
  4. Compare useful effects: Match light sound heat and movement outputs to possible product purposes. Explain why heat is not an appropriate decorative substitute for the request light.


Standard

  1. Draw two representations: Create a paper functional-role diagram for the request indicator and explain what a circuit diagram would add. Show the supply as a separate energy input.
  2. Trace a button sequence: Predict the output for release press continued hold release and a disabled press. Explain why the stated rule does not toggle or latch the output.
  3. Plan an inclusive indication: Compare labelled light sound and movement indications against attention setting and user needs. Do not rely on colour alone or assume that greater brightness or volume is always better.
  4. Write expected and observed cases: Make a test record covering all four logical combinations holding release disabled operation and missing power. Keep all actual results pending because no device has been tested.


Advanced

  1. Distinguish possible faults: An actual indicator is dark despite a reported enabled press. List several possible causes and explain why one observation cannot identify the fault. Describe a teacher-managed checking request without live rewiring.
  2. Change to a sensor input: For the separate invented below-forty condition evaluate readings thirty-nine forty and forty-one while enabled. Explain why the scale is not lux or a real sensor calibration and how to record missing information.
  3. Re-enable a held request: Under the original current-state rule predict the output if the button remains held while enable changes from false to true. Contrast the result with an event-based press-only rule which would need its own specification.
  4. Submit a complete conceptual analysis: Submit component roles diagrams a response rule expected cases output selection and remaining implementation questions. Distinguish conceptual correctness actual behaviour and school-observed physical competence.



Learning Check

  1. Separate role and form: Why should the chosen function determine input or output classification?
  2. Read the actual circuit: What does the provided schematic establish and leave unspecified?
  3. Explain responsive control: How does the request output respond to pressing holding releasing and disabling?
  4. Use the threshold boundary: How does the separate invented sensor condition classify thirty-nine forty and forty-one?
  5. Avoid a premature diagnosis: Why can an OFF indication have several explanations?
  6. Select and justify an output: What makes an output choice appropriate?


Worked checks and assessment guidance

  1. A button supplies information about a user action and an LED emits light in the original indicator. A sensor reading is input information even if it later appears on an output display. Some physical devices can serve more than one role in different arrangements so neither appearance nor a generic component label can replace a clearly stated system boundary and function.
  2. It shows one cell symbol and three resistor symbols connected in a single loop. It contains no switch LED or processor symbols and no numerical component values. The continuous series path can be described but it cannot be treated as a complete request-indicator implementation or used to infer a safe current brightness or component rating.
  3. With power available both enabled and currently pressed must be true. The light comes on during an enabled press stays on during a continued enabled hold and goes off on release or disabling. The rule does not retain an earlier request and does not require a new press if enable becomes true while the button is still held because it follows current states rather than only press events.
  4. The condition is strictly below forty on the invented scale. Thirty-nine is below the boundary while forty and forty-one are not so an enabled system would indicate only for thirty-nine under that rule. The logical example does not define lux lighting adequacy or a calibrated sensor. Missing information must remain unresolved rather than being filled with a guessed reading.
  5. It can follow from a released button disabled logic or unavailable power and may also reflect a connection output or other fault. A single visible state does not identify which condition applies. Compare expected cases with properly observed evidence through the teacher-approved procedure and do not respond by altering live connections or increasing the supply.
  6. It should produce the effect the user and context require with understandable meaning suitable access and an appropriate electrical implementation. A labelled visual indication may suit a desktop request while sound changes attention and hearing considerations and movement introduces mechanical questions. Heat requires a thermal purpose and specialist safety consideration rather than being treated as an interchangeable indicator.


Learning evidence

Submit a role table identifying supply inputs control and outputs for the fictional product. Add a functional system representation and a separate explanation of the actual cell-and-resistor schematic with its missing information.

Submit the four-state truth-table explanation a hold/release sequence a strict-threshold comparison and expected-versus-observed test plan. Leave actual observations pending. Justify an output against user needs and explain possible causes of a mismatch without claiming a certain fault from one symptom. Physical circuits require approved school arrangements and direct observation; no online result authorises mains work or proves electrical safety.


OER and Wikipedia

Department for Education: Design and technology, selected Key Stage 3 electrical and electronic systems — current original programme checked. The annual placement and all fictional control cases are editorial.

Micro:bit Educational Foundation: Inputs, outputs and processors — actual original body checked for information input, processing and output roles. No program transfer, hardware use or account is required.

Micro:bit Educational Foundation: LEDs and buttons — actual original body checked for LED light output and button input. No source project, copied images or hardware specifications are substituted for the separate fictional product.

Micro:bit Educational Foundation: Sensors, selected temperature and light explanation — actual original body checked. Sensor input is distinguished from the display output, and the documented dual use of micro:bit LEDs prevents an absolute single-role classification. No actual sensor calibration or environmental measurement is claimed.

Micro:bit Educational Foundation: Safety detail — actual current original guidance checked for approved power arrangements, damaged equipment, short circuits and supervision. This manufacturer's device-specific guidance is not a complete legal risk assessment for every school circuit; relevant approved equipment guidance and the responsible teacher remain necessary.

All About Circuits: Circuit With a Switch, selected switch-path explanation — actual original body checked for open/closed path reasoning. No household switch procurement, building procedure, live measurement or source graphic is adopted. The online exercise remains conceptual.

Commons: LEDs.jpg — Afrank99; CC BY-SA 2.0 (https://creativecommons.org/licenses/by-sa/2.0). Exact original record and actual preview checked; image unchanged.

Commons: Series circuit.svg — Mets501; CC BY-SA 3.0 (https://creativecommons.org/licenses/by-sa/3.0). Exact original record and actual preview checked; image unchanged.

LEDs.jpg credits Afrank99, own photograph dated 16 July 2005, CC BY-SA 2.0. Six components are shown; no ratings or actual light emission are inferred from casing colour. Series circuit.svg credits Mets501, own drawing dated 3 January 2009, offered as CC BY-SA 3.0 with GFDL also retained in the original record. Its transparent preview was viewed on a white browser background without changing the graphic: one cell and three resistors in one loop, no switch or LED.

European Space Agency, ESA: Blinking LED, Introduction to Tinkercad circuits, Part 1 — fresh title creator metadata and embed eligibility checked and actual simulation preview seen. No full-film or transcript review, open video licence, download or republication is claimed. A blink demonstration is not the original current-state request specification; no account or code transfer is required.

The request rule, logical combinations, sensor threshold and all tasks are original fictional teaching material. They are not observed test data, calibrated measurements, a complete wiring design, legal assessment or independent expert certification.


Linked learning areas


aiMOOC Projects



Schulfach+




aiMOOCs



aiMOOC Projekte









MOOCwiki · Deutsch

Nach dem Lernen ist vor dem Lernen

Entdecke direkt den nächsten Lernkurs. Weitere Inhalte erscheinen, wenn Du weiter nach unten scrollst.

Zur MOOCwiki-Hauptseite

Mediathek

Suche verfeinern

Dein Lernplan bestimmt, was oben steht. Alle anderen Inhalte bleiben erreichbar. Seitenaufrufe beeinflussen die Auswahl nicht.

Inhalte werden geladen ...

Mediathek wird aus dem Wiki geladen ...