Zum Inhalt springen

English:Design & Technology Year 5 - Strong and stable structures

Aus MOOCsWiki Staging
aiMOOC-Siegel aiMOOC

Design & Technology Year 5 - Strong and stable structures

QR-Code



Introduction

A truss bridge with visible diagonal members and supports. Its geometry can be observed, but a photograph is not a structural inspection or a way to establish its safe load.
A truss bridge with visible diagonal members and supports. Its geometry can be observed, but a photograph is not a structural inspection or a way to establish its safe load.

Why can a carefully shaped piece of card act differently from a flat sheet? Why might a frame lean sideways before any part breaks? In this course you will investigate folds, triangulation and bracing, distinguish ways a structure can fail, and use fair test evidence to propose a revision.

You will study a small desk-level card-beam model, not a real bridge for people or animals. The worked test data are explicitly fictional. For an actual model, the teacher chooses the materials, small loads, limits and supervision. You can complete the analysis with the supplied data if a practical session is unavailable; mark physical construction and testing as pending rather than claiming you performed it.

The Year 5 sequence is an editorial route through England's Key Stage 2 Design & Technology. Your learning evidence includes a labelled load-path sketch, two model versions or plans, a results table, a limited conclusion and an evidence-based improvement. No quiz or classroom model certifies a real structure's safety.


Follow the load and identify the failure

A structure is an arrangement of parts that carries or supports something. A load is an action on the structure, such as the weight of the model itself or an object placed on it. In a simple desk bridge, a downward load is transferred through the deck or beam to the supports and then the table. This route is called a load path.

Compression pushes parts together; tension pulls them apart. These describe loading, not whether an object is good or bad. A bent beam can have a compressed region and a tensioned region at the same time. A simple sagging beam between two supports, loaded downward near its middle, tends to compress its upper region and stretch its lower region. This is a simplified model, not a rule for every point of every bridge.

Stiffness concerns how much a structure deforms under a load. Strength concerns resisting failure under stated conditions. Stability concerns maintaining a position or configuration instead of tipping, sliding or changing shape unexpectedly. A structure can be stiff in one direction but still tip, so “it did not bend” is not a complete test of stability.

Four different observations. A deck may bend down noticeably. A slender upright may buckle, bending sideways under compression. An entire model may slip at a support. A tower may tip because its balance changes. A join can also open or tear. Record the observed mode rather than calling all of them “not strong enough”. Different failures suggest different investigations.

Worked diagnosis. Model A's beam stays almost straight, but its end slides off a support. Adding a thicker beam may not address the observed problem. Check support contact and the agreed setup first. Model B stays on its supports but its middle bends beyond the agreed limit; a change in section shape may be worth investigating. Neither observation proves what would happen at a different span or with a different load position.

Your load-path sketch. Draw a short beam and two level supports. Add a downward arrow at the centre, label the beam and supports, and explain how the supported load reaches the table. Do not invent exact force values. For the bridge photo, identify visible diagonals, the deck and the support locations; a photo cannot tell you every member's force or the condition of hidden connections.

A precise question. Replace “Which structure is strongest?” with “Under the same desk-level test, which of these two card sections stays within the agreed middle-deflection limit for more of the specified small load pieces?” That narrower question defines an observation you can actually compare. It does not turn a classroom trial into a professional load rating.


Use folds, triangles and bracing for a purpose

Folded sections. A flat strip has little depth in the direction it bends. Folding its long edges into a U-shaped channel changes where the card lies in the cross-section. That can increase resistance to bending for some loading directions without adding another sheet. The result depends on dimensions, orientation, creases and joints; do not assume every fold improves every structure.

In our example, both blanks begin as 200 mm by 100 mm rectangles of the same card. One stays flat. The other has a 20 mm strip folded up along each long edge, leaving a 60 mm horizontal middle section. Its overall horizontal deck width differs from the flat strip; this is part of the intended section-shape change. The initial card amount stays the same. Turn the channel sideways and it need not behave in the same way.

Layers and fluting give corrugated cardboard a shaped structure. The picture illustrates a construction principle; it does not show the course's two test specimens or their measured performance.
Layers and fluting give corrugated cardboard a shaped structure. The picture illustrates a construction principle; it does not show the course's two test specimens or their measured performance.

Triangulation. Imagine a four-sided frame with fixed-length sides and freely pivoting corner joints. In its plane, it can lean into a different shape without changing those side lengths. A fixed-length diagonal divides it into triangles and constrains that racking movement. A triangle with fixed side lengths does not change its angles freely in the same way. A three-dimensional structure may also need support against movement out of that plane. Real members and joints can still bend, stretch, buckle or fail, so “triangles cannot break” is false.

Bracing. A brace is an added member intended to resist an unwanted movement. A diagonal brace may triangulate a rectangular frame. A thin cord can resist a pull when taut but cannot act like a rigid member resisting compression; in a model intended to resist racking in both directions, its arrangement and slack matter. Do not label any decorative diagonal as effective bracing without checking connections and the intended loading.

Stabilising a model. A wider support footprint or a lower concentration of mass can make a simple model less prone to tipping in the relevant direction. On a level surface under gravity alone, the position of the centre of mass relative to the support region helps explain tipping. A tall model, a sideways push, poor joints or sliding can complicate the outcome. Do not treat a large-looking base as an unlimited guarantee.

Worked design choices. If a flat deck bends down, investigate a folded section. If a hinged rectangular frame racks sideways, investigate a well-connected diagonal. If a tower tips while its members stay straight, investigate its support footprint and mass arrangement. These are three different proposals tied to observations, not three interchangeable decorations.

Guided prediction. For the same card and span, predict whether a U-channel will stay within the chosen deflection limit for more small load pieces than the flat strip. State why, and name one reason the prediction could be wrong: for example, a damaged crease or an uncontrolled support contact. A prediction is not a result; retain it even if the trial disagrees.


Compare two versions with one agreed method

A useful test identifies the design change, the recorded outcome and the conditions kept consistent. Here the intended change is the section geometry: flat or U-shaped. Keep the card source, starting blank dimensions, span, supports, orientation, load pieces, load position, loading pace and stopping rule consistent. Different paper, a shorter gap or extra tape could explain a result if changed at the same time.

Proposed desk-level setup. The teacher approves two stable, low supports with a 150 mm clear gap on a protected table. A 200 mm specimen placed symmetrically leaves 25 mm supported at each end: 200 minus 150 leaves 50 mm, shared equally. Use teacher-prepared specimens, a marked midpoint and the same approved small load-spreading piece. Keep the area clear and use only the small loads and maximum count chosen by the teacher. Never climb on, hang a heavy bucket from or load a model with a person or animal.

Define the observation before testing. In the supplied fictional trial, a specimen passes a loading step when it remains on the supports, its joins remain sound and its middle deflection is no more than 5 mm. Stop at the first failing step or the teacher's maximum of 15 load pieces, whichever comes first. Never increase the limit to pursue a record. The teacher determines how deflection is measured consistently. The same load-spreading piece is present throughout; the counted pieces are added in the same position, one per step.

Use fresh matching specimens for repeats rather than straightening a previously damaged strip and calling it new. Inspect them first and record differences. The following results are invented to practise analysis; they do not show that any real sheet has these capacities.

Version Trial Last passing count First failing count Observed stopping reason
Flat 1 4 5 Middle deflection exceeds the agreed limit
Flat 2 5 6 Middle deflection exceeds the agreed limit
Flat 3 4 5 Middle deflection exceeds the agreed limit
U-channel 1 12 13 Middle deflection exceeds the agreed limit
U-channel 2 13 14 Middle deflection exceeds the agreed limit
U-channel 3 12 13 Middle deflection exceeds the agreed limit

Worked result. Flat last-passing counts are 4, 5 and 4; arranged in order, 4, 4 and 5, their middle value is 4. U-channel counts are 12, 13 and 12; the middle is 12. The difference between these medians is 8 load pieces. That is a comparison of these fictional results at the same stated endpoint, not a universal eight-piece improvement for any card.

Keep the first failing count distinct from the last passing count. In the first flat trial, 5 is not a supported success value. A result at 5 mm exactly would still meet the “no more than 5 mm” threshold; a value greater than 5 mm would not. Record any slip or join failure honestly rather than replacing it with a nicer bending result.

When the limit is reached. Another proposed version holds all 15 permitted pieces without failing. Write “passed through the 15-piece test limit; failure point not observed”. Its failure capacity is unknown. Do not call 15 the exact breaking load or add more pieces without permission. If two versions both reach the cap, this test does not distinguish their failure points.

Your own record. Before an approved practical trial, draw both versions, list controls and state a prediction. Record actual results in a new table with the date, conditions and stopping reason. If no trial occurs, use the supplied table for analysis and leave the practical objective open.


Improve the structure using what the evidence shows

A conclusion should answer the test question with specific evidence, explain its limits and lead to a suitable next question. “The channel is best forever” exceeds the data. “The U-channel's median last-passing count was 12 versus 4 for the flat version in these fictional tests” stays within the record.

Worked revision proposal. The channel specimens all stopped because their middles deflected too far; there was no supplied slip or join failure. A sensible next design might change the fold depth while keeping the starting card amount, span and loading procedure consistent. Predict an effect, draw the new section and record how the new horizontal width changes. Do not change card type and span as well and then attribute every difference to the folds.

If an actual frame racks, use a properly connected brace trial instead. If a tower tips, investigate the base or mass placement with approved low-level models. An improvement must address the observed failure mode; adding more mass high on a tipping tower could make the problem worse. A larger base may help in one direction without fixing sliding or loose joints.

The original Science Buddies Paper Bridges STEM Activity shows shaped paper bridges and small-load comparisons. Identify one shape change and one condition you would need to keep the same. The film's particular loading method is not automatically the method for your class: follow the school's agreed limits and endpoint. Our course uses a limited-deflection stop to avoid treating a destructive record attempt as the goal. The written cases provide the complete reasoning route if you cannot watch the video.

Three levels of evidence. A plan shows that you can choose controls and anticipate a result. Analysing supplied data shows that you can reason from a record. A supervised practical test provides observations of your actual model and method. These are related but different achievements. Do not claim that one automatically proves the others.

Critique an overclaim. A group tests a shorter channel span than the flat span and concludes that the fold alone caused the improvement. The result confounds shape with span. Keep the result but label its limit and propose a matched-span comparison. Deleting inconvenient observations is not a valid repair.

Communicate your improvement. Produce a short dossier with the problem, the two versions, labelled load paths, a prediction, controls, results or clearly labelled supplied data, a conclusion and one revised sketch. State which part of the record justifies the revision. Identify what must be checked before making or testing it.

Teacher feedback can ask for clearer evidence, a better control or a more appropriate failure diagnosis. It should not rank a learner's worth by how many counters a model holds. A carefully reported failed model can demonstrate excellent design reasoning when the conclusion and next step are sound.


Interactive Tasks


Quiz: Test Your Knowledge

Which description explains compression? (Loading that pushes parts together) (!A pull that always separates parts) (!A decorative colour scheme) (!A guarantee against tipping)



A beam stays straight but its end slides off a support. What should the record say? (The observed failure is slipping at a support) (!The beam must have broken in tension) (!The result proves every material is weak) (!The observation can be erased because it is inconvenient)



Why can a fixed-length diagonal help a freely jointed rectangular frame? (It constrains racking by forming triangles) (!It makes every joint impossible to break) (!It removes every load from the frame) (!It turns a cord into a rigid compression member)



What is kept the same in the intended flat-versus-channel comparison? (Card source, starting blank, span and loading method) (!Only the colour of the notebook) (!A different span for every trial) (!A different load position for every design)



A two-hundred-millimetre specimen spans a one-hundred-and-fifty-millimetre gap symmetrically. How much sits on each support? (Twenty-five millimetres) (!Fifty millimetres) (!One hundred millimetres) (!Ten millimetres)



Which count is a success value in the first supplied flat trial? (Four pieces, the last passing count) (!Five pieces, the first failing count) (!Any count above fifteen) (!The count the designer hoped for)



What is the difference between the supplied medians of twelve and four? (Eight load pieces) (!Sixteen load pieces) (!Three load pieces) (!A universal strength value in kilograms)



A new version reaches the fifteen-piece limit without failing. What follows? (It passed through the limit and its failure point remains unknown) (!Its exact failure count is fifteen) (!The learner should add heavy objects without permission) (!It proves unlimited load capacity)



Which proposal responds most directly to an observed tipping problem? (Investigate the support footprint and mass arrangement) (!Automatically add more mass at the top) (!Hide the tipping observation) (!Change the notebook colour only)



What can analysing the supplied fictional table demonstrate? (Reasoning from data without claiming an actual practical test) (!Certified safety of a real bridge) (!Proof that the learner has built every model) (!A professional safe-load rating)





Memory Game

Load Action on a structure such as a supported weight
Compression Loading that pushes parts together
Tension Loading that pulls parts apart
Bracing Adding a member intended to resist unwanted movement
Buckling Sideways deformation of a member under compression
Stability Maintaining position or configuration rather than tipping or sliding
Control variable Condition kept consistent in a comparison





Drag and Drop

Bending The middle of the model deck curves down
Buckling A slender upright bends sideways under compression
Slipping A beam end moves off its support
Tipping The whole tower overturns without a broken member
Racking A freely jointed rectangular frame leans into another shape





Crossword Puzzle

TENSION Loading that pulls parts apart
COMPRESSION Loading that pushes parts together
BRACE Member added to resist unwanted movement
STABILITY Resistance to tipping or unwanted movement
BUCKLING Sideways deformation under compression
MEDIAN Middle value when trial results are put in order





LearningApps

Optional extra practice. Choose an appropriate activity with your teacher. If the external collection is unavailable, use the native activities and independent tasks in this course.


Cloze Text

Complete the explanation.
A supported weight is a

. A pushing action can cause

. A pulling action can cause

. A diagonal member may act as a

. A slender compressed member may fail by

. Keeping a model from tipping concerns

. Consistent conditions support a

comparison. The middle ordered result is the

.



Open Tasks


Easy

  1. Load-path drawing: Draw a desk bridge with a downward central load, beam and two supports. Explain the route to the table without inventing force values.
  2. Failure cards: Create five labelled sketches showing bending, buckling, slipping, tipping and racking. Explain why they do not all call for the same improvement.
  3. Three structural ideas: Explain a fold, triangulation and a brace using drawings. State a condition or limit for each, including the importance of the members and connections.
  4. Table reading practice: Find the last passing and first failing count for each supplied trial. Explain why a first failing count is not a demonstrated success value.


Standard

  1. Prediction and controls: Plan a comparison of flat and channel card sections. State the single intended design change, controlled conditions, prediction, agreed endpoint and teacher-approval points.
  2. Two-version practical record: If approved and supervised, construct or use two prepared versions and test them by the same agreed small-load method. Keep a real dated table and stop at the limit. If no session is possible, identify practical testing as pending and analyse the supplied data instead.
  3. Evidence-based conclusion: Use all six supplied rows to calculate each median and the difference. Write a limited conclusion, an uncertainty and a proposed follow-up.
  4. Revised structure sketch: Choose one observed failure mode and sketch a change intended to address it. Explain the mechanism, what will remain constant and what an approved test would need to show.


Advanced

  1. Limit-reached reasoning: A version passes every step to the approved maximum with no failure. Explain how to record this result and why it does not establish an exact failure capacity or justify increasing the load.
  2. Confounded test critique: One group shortens the channel span while changing its section. Identify the confound, preserve the result with a limitation, and design a matched comparison.
  3. Brace direction investigation plan: Compare a rigid diagonal and a taut cord in a hypothetical freely jointed frame. Explain the difference between tension and compression behaviour and plan an approved low-force conceptual demonstration without claiming all braces act identically.
  4. Structural design dossier: Prepare a complete explanation, two-version plan, actual or clearly labelled supplied data, revised sketch and reflection. Distinguish your reasoning evidence from practical observation and real-world structural certification.



Learning Check

  1. Three purposeful changes: Explain how folded sections, triangulation and bracing can improve a model, including the conditions that matter.
  2. Failure diagnosis: A model slips at the end, another deflects in the middle and a tower tips. Propose a relevant investigation for each.
  3. Fair test design: Specify a prediction, controls and endpoint for the two card versions. Explain the twenty-five-millimetre support overlap.
  4. Numerical conclusion: Calculate the medians from flat counts four, five, four and channel counts twelve, thirteen, twelve. Explain the difference and its limit.
  5. Unknown capacity: Interpret a version that reaches the approved fifteen-piece maximum without failing.
  6. Evidence-led revision: Propose one improvement using an observed stopping reason and state how you would evaluate it.


Worked checks and assessment guidance

  1. Folds change section geometry and can resist the tested bending direction; a fixed diagonal constrains racking in a freely jointed frame by forming triangles; a brace resists a specified movement when properly connected. Real members and joints may still deform or fail, and a cord cannot resist compression like a rigid strut.
  2. Investigate support contact/setup for slipping, section geometry and bending behaviour for middle deflection, and support footprint/mass arrangement for tipping. Tie proposals to observations and do not claim thicker material fixes every mode.
  3. The prediction links section change to the stated outcome. Keep card, blank, span, orientation, support setup, load pieces and placement, pace and stop rules consistent. A 200 mm specimen across 150 mm leaves 50 mm total or 25 mm each when centred. Stop at the first agreed failure or approved cap; physical testing requires supervision.
  4. Sorted counts are 4, 4, 5 and 12, 12, 13; medians are 4 and 12, difference 8 pieces. It describes the fictional samples under the same defined endpoint. First-failing values are not last-passing successes, and the result is not a universal material strength or safe-load rating.
  5. Record that it passed through 15 pieces under the method and the failure point was not observed. Do not claim 15 is its exact failure load, assume unlimited capacity or extend the test without approval. Two capped results may not reveal which failure point is greater.
  6. Accept a justified geometry change for bending, a connected brace for racking or a relevant stability change for tipping. State a controlled approved follow-up and a possible trade-off. Keep original observations and distinguish a prediction, supplied-case reasoning and actual practical evidence.


Learning evidence

Retain labelled load and failure sketches, explanations of folds/triangulation/bracing, a two-version prediction and controlled method, a complete results table, median reasoning and a justified revised design. Clearly distinguish actual supervised trials from supplied fictional data. A learner's physical build/test objective stays pending if only the conceptual route has been completed.

Assess the links between observation, explanation and revision separately from load count. Provide diagrams, vocabulary support, larger pre-folded models or oral reporting as appropriate. Do not rely on colour alone. Direct teacher observation and school approval are required for practical construction and testing; no result in this course certifies a structure for people, animals or real loads.


OER and Wikipedia

Sources checked on 11 November 2026. The card specimens, endpoint and six-row data table are original fictional teaching cases, not published experimental findings.

Department for Education: Design and technology programmes of study, Key Stage 2 Technical knowledge and Evaluate. The Year 5 route is editorial.

Australian National University: Paper Bridge Challenge and Science Buddies: Paper Bridge Design Challenge provide primary educational background on investigating shape and controlled comparisons. Their particular experiments differ from the limited-deflection method in this course. Exploratorium: Balance and centre of gravity provides an introductory balance reference; the text states the limits of the simple support model.

The embedded Paper Bridges STEM Activity, original Science Buddies video, is a visual example. It is embedded rather than copied or claimed to be openly licensed. Use available captions and playback controls; the independent text and supplied data support access without watching.

West Fork Pigeon River Pratt Truss Bridge, Bethel, NC.jpg, Warren LeMay, CC BY-SA 4.0. Corrugated Cardboard.JPG, Richard Wheeler (Zephyris), CC BY-SA 3.0. Images embedded without alteration. Neither photograph is an inspection, capacity test or a view of the fictional trial specimens.

The encyclopedia overview below is optional context. It does not establish the condition or safety of the photographed bridge.


Linked learning areas


aiMOOC Projects



Schulfach+




aiMOOCs



aiMOOC Projekte









MOOCwiki · Deutsch

Nach dem Lernen ist vor dem Lernen

Entdecke direkt den nächsten Lernkurs. Weitere Inhalte erscheinen, wenn Du weiter nach unten scrollst.

Zur MOOCwiki-Hauptseite

Mediathek

Suche verfeinern

Dein Lernplan bestimmt, was oben steht. Alle anderen Inhalte bleiben erreichbar. Seitenaufrufe beeinflussen die Auswahl nicht.

Inhalte werden geladen ...

Mediathek wird aus dem Wiki geladen ...